Maintenance methods of metal circular saw machine
Release time:
2022-10-14 10:34
Source:
The quality of metal circular saws directly affects the service life. When using them, you need to know that poor quality circular saws will also affect the normal use in the later period. However, if you only have good quality, but do not pay attention to maintenance, the service life will be greatly shortened. Therefore, regular care can maintain the normal working condition of the machine and extend the service life of the metal circular saw.
When repairing the metal circular saw, check the amount of lubricating oil, that is, the amount of oil to be used, and strictly follow the lubrication diagram to keep the oil (grease) and perform maintenance. The amount of oil is appropriate and the oil circuit is unobstructed. There is no rust, no root oil, no "yellow robe", no scratches on the sliding surface, and see if the oil color changes or deteriorates. If there are no problems with these, it is recommended to check the appearance, whether the parts are intact, and ensure that the safety device is safe and reliable. Then you can look at the power supply. Just like the solid bar metal circular saw, check the power cord, check the motor wiring, and whether the electrical device is short-circuited. This is the normal power-on state. Therefore, if you look at the first three points, you can move the motor of the metal circular saw machine to make the metal circular saw machine run, but it can only be idling, not working directly. When the idling time reaches 10 minutes, check and adjust the various parts of the main drive. The metal circular saw machine must be in normal operation, whether the direct drive of the belt is properly tight, whether the direction and spacing of the circular saw blade are installed correctly, and whether there is any looseness; then you can check and adjust the hydraulic system to make its handle flexible, "clamp", "feed", "feed", "return" and "release" actions accurate, the hydraulic oil is not lower than the scale line, and the pump works reliably.
When repairing the metal circular saw machine, you should also pay attention to it. For example, if you find that the sound of the metal circular saw machine is abnormal, you should stop the machine in time, check it, and check the main drive. Of course, whether the hydraulic, cooling system and vise of the metal circular saw machine work normally, whether the hydraulic and cooling systems are noisy or leaking, according to the amount of oil in the tool box, the oil amount should not be lower than the mark line on the oil mark at 1/3 of the height. Here we also remind everyone to always pay attention to the operation, temperature rise, sound, vibration, etc. of motors and electrical appliances. The speed of operation should be kept consistent and not too fast, so as to avoid the metal circular saw machine working under load. When the metal circular saw machine is in operation, the guide rails and columns are often strained, so once the guide rails and columns are found to be strained, the work should be stopped and repaired in time. Especially when the metal circular saw machine is in operation, the belt will flip over. If the belt is found to be overturned or damaged, it should be repaired or replaced in time. Check or replace the input power fuse.
Related News
What is the reason why the metal circular saw machine is not sharp and how to solve it?
The impact of the circular saw blade of the metal circular saw machine is not very large, such as cutting too large workpieces, the surface of the workpiece is not smooth, and the production efficiency is reduced. How to prevent the metal circular saw blade from being too blunt? Let's take a look at the factors and solutions for the sharpness of the metal circular saw machine blade!
High-speed metal circular saw machine saw blade maintenance precautions
Maintaining good working habits and formulating a strict maintenance system will help the smooth operation of the equipment. Metal circular saw machines, especially saw blades, must be carefully cleaned before or after work.
How to operate a metal circular saw
The metal circular saw machine is hydraulic, with vertical slides moving up and down, a firm feeding structure, accurate movements, and a floating material seat that does not damage the surface of the workpiece. Next, I will introduce the operation method of the metal circular saw machine.
Operating rules and characteristics of metal circular saw machines
The metal circular saw machine is hydraulic, with vertical guide rails for up and down advance and retreat, a firm feeding structure, accurate movement, and the floating seat does not damage the surface of the workpiece. The following is an introduction to the operation process and characteristics.
Practical Uses of Metal Circular Saw Machines
Metal circular saw machine is a form of circular saw. What are the practical uses? Here is a brief introduction to this question. Practical application of metal circular saw machine:
Advantages of using a metal circular saw machine
Metal circular saw machine is an industry that has emerged in recent years and belongs to metal cutting machinery and equipment. Many companies choose band saws or traditional old-fashioned equipment when processing metal materials, so companies must choose and replace new equipment now.
Address: Miaogang Road, Yongle Industrial Park, Leyu Town, Zhangjiagang City, Jiangsu Province
Page Copyright: Zhangjiagang Hehe Machinery Co., Ltd. Website Construction:China Enterprise Power Kunshan SEO